Bottom Brackets

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The BB30 for SRAM DUB Road comes in two versions; one using our CeramicSpeed Standard Bearings and the other using our Coated Bearings for even longer lifetime and lower friction. Compatible with: - Frame: BB30 - Opening diameter: 42mm - Shell width: 68mm - Bottom Bracket Tool for installation: BBT-79 In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker Sheet

The BB30 standard opened up design possibilities for frames. Adapting it for Shimano cranks takes a special machined aluminum threaded bottom bracket that threads into itself. Ours are finished with CeramicSpeed Bearings. You have two choices in terms of bearings. The first choice is our low drag, long life standard bearing with hardened-steel races and our super-round CeramicSpeed Balls. The second choice is our coated bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. This bottom bracket works with cranks that have 24mm spindles. Bottom brackets have several variables, but within that, CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings see another big bump in performance. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. Performance can be tuned by changing the grease. All Round Grease comes installed, but can be changed for lower drag TT and Track Grease, or higher durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box: - 1 bottom bracket with bearings installed - 2 dust covers installed - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed Bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. You have two bearing choices. The first choice is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second choice is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: BB86 - Opening diameter: 41mm - Shell width: 86.5mm In the box: - 2 CeramicSpeed Bearings - 2x dust covers - Plast-sheet - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker Sheet

Shimano cranks fit into BB86 frames when you have this CeramicSpeed Bottom Bracket installed. The kit consists of two cups that are pressed into either side of the central opening. The cups come with CeramicSpeed Bearings installed. There are two versions. The first is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed Balls. The second version is our coated bearing, which uses those same CeramicSpeed Balls installed on coated, hardened-steel races for longer life and less bearing drag. This CeramicSpeed BB86 Bottom Bracket works with cranks that have 24mm spindles, including both Shimano and FSA. CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That represents an average 75% drag reduction compared to standard bottom brackets. The hardened-steel races feature the CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings drop friction further and increase lifespan. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. In The Box: - 2 bottom bracket cups with bearings installed - 2 dust covers with integrated spacers installed - Spacer tube - 10ml syringe of All Round Grease - Sticker sheet

These bottom brackets are equipped with hand-built coated bearings specially developed for off-road performance that offer extreme durability and feature a unique design for SRAM DUB 28.99mm cranks. Coated bearings utilize the highest-quality CeramicSpeed ceramic balls, running on hardened-steel races with a 3-micron-thick metallic coating that makes the races corrosion-resistant, harder, and smoother, increasing service life and reducing friction. - This product has a unique design specifically for SRAM DUB 28.99mm cranks - Native fit frame interface and no plastic adapters or excess spacers - This design features a custom integrated dust cover for maximum durability In the box: - 2 CeramicSpeed Bearings - 2 dust covers - Plast sheet - 1 x 3mm spacer - 2 x 1mm spacers - 10ml syringe of CeramicSpeed Long Life Grease - Sticker sheet

The BB86 mountain bike standard was designed to integrate bearings into the bottom bracket for weight reduction. This kit works with the standard: it consists of two cups that are pressed into either side of the shell. There are two versions of this bottom bracket. Both come with CeramicSpeed Bearings installed into cups. The first is our long-life, low-drag Standard Bearing with hardened-steel races and our CeramicSpeed super-round, super hard balls. The second is our Coated bearing, which uses those same CeramicSpeed Balls installed on coated, hardened-steel races for longer life and less bearing drag. This CeramicSpeed BB86 Bottom Bracket meshes with cranks that have 24mm spindles, including both Shimano and FSA. CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That means an average 75% drag reduction compared to standard bottom brackets. The hardened-steel races feature CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings drop friction further and increase lifespan to applying a coating to the races. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. In The Box - 2 bottom bracket cups with bearings installed - 2 dust covers with integrated spacers installed - Spacer tube - 10ml syringe of LongLife Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design, while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed Bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The BSA for SRAM DUB Road comes in two versions. The first is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: BSA - Opening diameter: Threaded - Shell width: 68mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet - Spacertube

BSA is equivalent to English threading. English threading on MTBs mean a 73mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit works with 24mm diameter cranks, such as Shimano, FSA, Rotor, and others. Choose between two bearing types for the cups. Standard Bearings have low drag thanks to hardened-steel races and our Ceramic balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. For MTBs, English threading, thanks to history, is pretty much the one threaded standard. It works great. 24mm spindles easily fit through the shell, allow for large bearings to be employed in the outside cups. What's more, they rarely creak and seal up well. Lots of things slow bikes down; bearings shouldn't be among them. CeramicSpeed Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. The bearings last at least 3x longer than other bearings. Coated bearings have even less drag. These bearings come packed with LongLife Grease, best for muddy conditions. For less drag when riding in cleaner environs, you can coat the bearings with either All Round Grease or lowest drag TT and Track Grease, which is designed for clean conditions. In The Box - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10ml syringe of LongLife grease - Sticker sheet

BSA is equivalent to English threading. English threading on road bikes mean a 68mm-wide, 34mm inside diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit works with 24mm diameter cranks, such as Shimano, FSA, Rotor, and others. Choose between two bearings for the cups. Standard Bearings have low drag thanks to hardened-steel races and our Ceramic balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. English threading is easy to work with, and 24mm spindles easily fit through the shell, allowing for large bearings to be employed in the outside cups. Put more of your energy into forward motion by reducing frictional drag wherever you can. CeramicSpeed Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. CeramicSpeed balls are 100% smoother and 15% harder than ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10mm syringe of All Round Grease - Sticker sheet

BSA is another way of stating English threading. The initialization comes from Birmingham Small Arms, which made bicycles. English threading on road bikes mean a 68mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit allows you to fit 30mm cranks, like those from Rotor, to fit in the tight space of this 34mm spindle. Choose between two bearings types for the cups. Standard Bearings have low drag thanks to hardened-steel races and our CeramicSpeed Balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Note that the threaded extensions of this BB's cups that thread into the frame are thin, as they need to fit a 30mm spindle inside the cups. CeramicSpeed standard bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - 10ml syringe All Round Grease - Sticker sheet - Spacertube

BSA comes from Birmingham Small Arms, aka English threading. English threading on mountain bikes means a 73mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit allows you to fit 30mm cranks, like those from Rotor or RaceFace, to fit in the tight space of this 30mm spindle. CeramicSpeed Coated Bearings are hand-built with unique CeramicSpeed Ceramic Balls installed on coated, hardened-steel races for longer life and less bearing drag compared to standard bearings. In The Box - 2 threaded cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - 10ml syringe All Round Grease - Sticker sheet

The EVO386 standard is designed for oversized spindles. CeramicSpeed's kit for Shimano allows you to install Shimano or FSA cranks with 24mm spindles. The cups come with CeramicSpeed Bearings installed. Both CeramicSpeed Standard and Coated Bearings are available. Both utilize super smooth CeramicSpeed Balls and hardened-steel races. The latter has an additional metallic coating on the races to further smooth and harden the steel, further increasing life and lowering drag. The design of overlapping cups extending through the shell for EVO386 reduce the likelihood of creaking and increase the reliability of the system. The CeramicSpeed Standard Bearings feature an average drag reduction of 75% compared to stock bottom brackets. That translates into frictional drag of 0.3-0.4 watts per set, which is the result of great design, hardened-steel races, and ceramic balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Coated Bearings are a step up as they reduce drag by 50% compared to our Standard Bearings and an improvement in bearing life by 60%. All Round Grease comes standard in the bearings, but can be replaced for lower drag TT and Track Grease or higher durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box: - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker Sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The PF30 for SRAM DUB Road comes in two versions. One version uses our low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second version uses our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: PF30 - Opening diameter: 46mm - Shell width: 68mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

The PF30 standard has opened design possibilities for mountain bikes. Our CeramicSpeed PF30 Shimano MTB Bottom Bracket gives you the ability to install Shimano and other 24mm diameter spindle cranks on your PF30 MTB. Our PF30 cups have extended sleeves and join with a center section, reducing the likelihood of creaking and increasing the reliability of the system. There is both a Standard and Coated version. Both feature super smooth CeramicSpeed Balls and hardened-steel races. The CeramicSpeed Coated Bearings have an additional benefit: a 3-micron thick metallic layer over the races. This addition makes the races harder and smoother, lowering drag and increasing life. The CeramicSpeed Standard Bearings have only 0.3-0.4 watts of frictional drag per set, an average drag reduction of 75% compared to stock bottom brackets. This is the result of great design, including hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. They also last longer. If you want longer life and even lower drag, opt for the CeramicSpeed Coated Bearings. Life increases by 60% and drag drops by 50% compared to our CeramicSpeed Standard Bearings. Performance can be tuned by changing the grease. LongLife Grease comes installed, but can be changed for lower-drag All Round Grease for lower drag and cleaner riding conditions. In The Box - 1 bottom bracket with CeramicSpeed bearings installed - 2 dust covers - 5 0.85mm spacers - 10ml syringe of LongLife Grease - Sticker sheet

The PF30 standard is widely used. To make it compatible with Shimano and other 24mm diameter cranks, as well as improve the system, select this bottom bracket. The package comes with two cups and CeramicSpeed Bearings installed. The cups have extended inner sleeves and join with a center section, reducing the likelihood of creaking and increasing the reliability of the system while also eliminating spindle rub on internal cables. The cups mate with 24/22mm crank spindles. There are two bearing options. Both Standard and Coated Bearings feature super smooth CeramicSpeed Balls and hardened-steel races. The CeramicSpeed Coated Bearings have an additional feature: a 3-micron thick metallic layer over the races. This addition makes the races smoother and harder, lowering drag and increasing life. The CeramicSpeed Standard Bearings have only 0.3-0.4 watts of frictional drag per set, an average drag reduction of 75% compared to stock bottom brackets. This is the result of great design, including hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. They also last longer. The CeramicSpeed Coated Bearings last even longer and feature even lower drag. Life increases by 60% and drag drops by 50% compared to our CeramicSpeed Standard Bearings. All Round Grease is installed in the bearings. It can be replaced for lower-drag TT and Track Grease or higher-durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker sheet

The PF4130 bottom bracket is Press Fit into 41mm diameter shells that are 86.5mm wide and mate most cranks with a 30mm spindle to that standard. If you have a BB86 frame and want to install a 386EVO crank or Rotor 30mm crank, this is the kit you need. CeramicSpeed bearings are installed in cups. The Standard Bearing has ceramic CeramicSpeed balls and hardened-steel races. The Coated Bearing has the same balls running on hardened-steel races with a 3-micron-thick metallic coating making the races harder and smoother, increasing service life and reducing friction. Enjoying the benefit of a massive, strong, and light 30mm crank spindle in your BB86 frame is possible with this kit. Press in the cups, set up the wave washer, add spacers if necessary, and torque down. CeramicSpeed's bottom bracket is also stiff and light, but its greatest benefits come in the form of drag reduction. Standard Bearings with stock grease typically have frictional drag of 0.3-0.4 watts per set. That's about a 75% drag reduction compared to conventional bottom brackets. The bearings also last at least three times longer than other bearings. Performance can be tuned by replacing grease. All Round comes with this BB, but you can change it to TT and Track Grease for less drag or to LongLife for greater durability. In The Box - 2 cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - Plastic cable protector - 10ml syringe All Round Grease - Sticker sheet

The BB30 bottom bracket allows you to pair 30mm spindle cranks to 42mm inner diameter bottom bracket shells. Cannondale pioneered this standard along with specially-designed cranks and many have found the benefits to them. Road versions have a 68mm width, MTB has 73mm. These are also the bearings you can use to replace bearings in PF30 cups. You have two bearing choices. The first choice is our low drag, long life Standard Bearing, with hardened-steel races and our super-round CeramicSpeed balls. The second choice is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. BB30 was designed to make the bike lighter: no cups, threading, or redundant metal, plus a lighter, stiffer crank. That's why the crank spindle is 30mm, which was a big jump up from square-taper spindles. CeramicSpeed standard bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The bearings last at least three times longer than other bearings. In The Box - 2x bearings - 2x 1mm spacers - 2x 0.5mm spacers - 2x dust covers - O-ring - 10ml syringe of grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The BBright for SRAM DUB Road comes in two versions. The first is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: BBright - Opening diameter: 46mm - Shell width: 79mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

BBright is the Cervelo bottom bracket standard found on most of their frames, save the P5. In order to fit Shimano and FSA cranks into this oversized shell, this bottom bracket, complete with CeramicSpeed Bearings, needs to be pressed in. The BBright bottom bracket comes with either CeramicSpeed Standard or Coated Bearings installed. Super smooth, super-round CeramicSpeed Balls contained in hardened-steel races are found on both versions. The Coated version has a metallic coating laid onto the races, making it even smoother and harder, resulting in lower drag and longer life. BBright is similar to BB30, but is wider on the non-drive side. As such, the bottom bracket for running 24mm diameter cranks from Shimano, FSA, and others, is unique. The CeramicSpeed Standard Bearings last at least three times longer than other bearings. Thanks goes to hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. These have a frictional drag of 0.3-0.4 watts per set, which represents an average 75% drag reduction compared to most BBs. The CeramicSpeed Coated Bearings reduce drag by 50% compared to CeramicSpeed Standard Bearings, and show an improvement in bearing life by 60%. In The Box - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker sheet

BSA is another way of stating English threading. The initialization comes from Birmingham Small Arms, which made bicycles. English threading on road bikes mean a 68mm wide, 34mm inside diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit works with 24mm diameter cranks, found on cranks from Shimano, FSA, Rotor, and others. Choose between two bearings for the cups. Standard Bearings have low drag thanks to hardened-steel races and our Ceramic balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. 24mm spindles easily fit through the shell and allow for large bearings to be employed in the outside cups. Put more of your energy into forward motion by reducing frictional drag wherever you can. CeramicSpeed Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. CeramicSpeed balls are 100% smoother and 15% harder than ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10mm syringe of All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The EVO386 for SRAM DUB Road comes in two versions. The first version uses our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second version uses our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: EVO386 - Opening diameter: 46mm - Shell width: 86.5mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 2 x 3mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design, while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The ITA for SRAM DUB Road comes in two bearing options. The first option is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second option is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: Italian BB - Opening diameter: Threaded - Shell width: 70mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet - Spacer tube

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design, while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The PF30A for SRAM DUB Road comes in two versions. The first version uses our low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second version uses our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: PF30A - Opening diameter: 46mm - Shell width: 73mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 2 x 3mm spacers - 10 ml syringe of CeramicSpeed All Round Grease - Sticker sheet

This bottom bracket is perfect for when you have a PF30, BBright, or 386EVO shell frame and want to install a crank with a 30mm spindle into the frame. All these frame standards have a 46mm inner diameter and smooth insides, though the widths vary from 68mm to 86mm. This bottom bracket features nearly zero loss of power due to friction, thanks to the CeramicSpeed's incredibly efficient bearings. Choose either our Standard or Coated Bearings—both have super-round, super-smooth CeramicSpeed balls rolling on hardened-steel races. The Coated version has a metallic coating laid onto the races, making them even harder and smoother and resulting in longer life and lower drag. They come installed in cups. 30mm spindles on cranks are increasingly popular because of the high stiffness and low weight. 46mm inner diameter bottom brackets are popular for the freedom they offer designers in building frames. Because of the variety of widths, the cups here extend into the shell and come with a telescoping spacer tube to further seal and stiffen the system. The bottom bracket is already stiff thanks to hard ceramic bearings and hardened-steel races. Thanks to CeramicSpeed, it also generates nearly zero drag. Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction versus conventional BBs. The bearings also last at least 3x longer than other bearings. You can change the grease to fine-tune your BB's performance characteristics. TT and Track, All Round, and LongLife are greases CeramicSpeed designed. The first has the least drag, while the last is the most durable. All Round, in the middle, comes standard in road bearings. In The Box - 2 cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - Spacer tube - 10ml All Round Grease - Sticker sheet

The Hellbender 110 Bottom Bracket provides an incredible mix of performance and longevity through the inclusion of Enduro XD-15 ceramic bearings. These bearings feature nitrogen-infused stainless steel races that will not rust or corrode paired with Silicon Nitride ceramic balls. - T47 for 30mm Spindles - Lifetime Guarantee

The Hellbender 110 Bottom Bracket provides an incredible mix of performance and longevity through the inclusion of Enduro XD-15 ceramic bearings. These bearings feature nitrogen infused stainless steel races that will not rust or corrode paired with Silicon Nitride ceramic balls. - Enduro XD-15 ceramic ball bearings are made from pure silicon nitride material with extreme high density and uniform compaction - The race material is an advanced stainless alloy that is nitrogen infused and will not rust or corrode - Dual stage anodize black and gold machined aluminum bottom bracket cups - Kluber NBU52 grease runs better and smoother with time and is highly resistant to being washed out - Designed for use with 30mm spindles

BB90 is the Trek oversized bottom bracket standard and is only found on Trek road bikes. The shell is 90.5mm wide and is designed to work with 24mm spindles and road cranks and have the bearings inside the shell. The CeramicSpeed Bearings come as two bearings, which are then pressed into the frame. Those two bearings consist of either CeramicSpeed Standard or Coated Bearings. Both feature super smooth, super-round CeramicSpeed Balls contained in hardened-steel races. The Coated version has a metallic coating laid onto the races, making it even smoother and harder, resulting in lower drag and longer life. -BB90 is simple and light. The standard is designed to work with 24mm spindles. The bearings work with Shimano and other 24mm cranks, like FSA. - The CeramicSpeed Standard Bearings last at least 3 times longer than other bearings. That's thanks to hardened-steel races and CeramicSpeed Balls that are 100% smoother & 15% harder than the ceramic competition. These bearings have a frictional drag of 0.3-0.4 watts per set, which represents an average 75% drag reduction compared to stock BBs. - The CeramicSpeed Coated Bearings reduce drag by 50% compared to Standard Bearings and an improvement in bearing life of 60%. In The Box: - 2 BB90 bearings - 2 seals - 2 dust covers with integrated spacers - 10ml syringe of All Round Grease - Sticker Sheet

The Wheels Mfg BB30 Outboard bottom bracket will give you all of the same benefits as their other Outboard style BBs. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing 24mm spindle diameter cranks (Shimano, FSA, Etc.) in BB30 frames without the need for adapters. - Bearings: Enduro ZERØ Ceramic - Color: Red - Bottom Bracket/Frame Interface: BB30, Specialized Alloy OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 42mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 122g

PF30 Threaded bottom bracket features two machined aluminum cups that thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Directly replaces all OEM PF30 bottom brackets. Note: Use only bottom bracket tools compatible with 16-notch, 48.5mm outer diameter cups. - Bearings: Enduro ZERØ Ceramic Hybrid - Color: Black - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB, BBRight™ Press Fit - Bottom Bracket Shell Width (mm): 61mm to 79mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: BB30 - Crank Spindle Diameter: 30mm - Weight: 106g

- Ceramic bottom bracket for DUB spindle cranks Specs: - BB Shell Type: BB30 - BB Shell Width: 68/73mm - BB Bearing: Ceramic - Crank Spindle Diameter: 28.99mm - Interface: DUB - Cup Diameter: 42mm